Click To Call(727) 591-3365Click To Get A Free Estimate
Sealed brick paver driveway at a home in Gateway

Paver sealing for Gateway homes

Paver Sealing in Gateway, FL

Gateway townhomes, condos and houses near Highway 92 and I-275 get a free sealing estimate when you call (727) 591-3365.

  • Brings out deeper paver color
  • Fresh joint sand helps lock pavers in place
  • Gives weeds less room to grow
  • Makes the surface easier to keep clean
  • Free estimate, no obligation

Request a Free Estimate

Free, no obligation.

Step 1 of 2

Where are your pavers?

Please choose one.

Free EstimateNo obligation
Fast ReplyWithin 1 business day, usually much sooner
Typical Local Price$1.25 to $2.50 a sq ft to clean, sand and seal
Call Now(727) 591-3365
Paver sealing

Fast, careful paver sealing in Gateway

Paver sealing is available in Gateway, for apartment entries, townhome drives, condo pool decks and the houses that sit between them. One local contractor can wash the pavers, replace the sand and seal them, and the estimate costs nothing. Reach out by calling (727) 591-3365, and a reply comes within 1 business day, usually much sooner.

Maybe the walk to your building has faded to chalk, with weeds in the seams and a green film by the stairs. After a wash, fresh sand and a new coat, that same walk looks even and clean. A manager or an owner can request a free estimate and ask for a written scope with every area listed. The estimate is free.

Call (727) 591-3365

Family relaxing by a sealed paver pool deck near Gateway
Why hire local

Why hire a local paver sealing contractor in Gateway?

Gateway has more apartments and townhomes than houses, so the person who orders paver sealing may be a manager or a board. A local contractor can write the estimate for either, and you can request a free estimate to start.

Property walk, no fee

A local contractor tours your Gateway entries, decks or drive and writes the scope down, at no charge.

For comparing bids

Start from the $1.25 to $2.50 per square foot that Tampa Bay companies commonly publish.

Finish choice

At busy entries matte hides scuffs. Wet look brings out deeper color, though scuffs show sooner.

Your group decides

An owner, a manager or a board picks the date. Requesting an estimate does not tie your group to a contractor.

Get Your Free Estimate in Gateway

Tell us about your pavers in Gateway.

Call (727) 591-3365

Free, no obligation

Paver joint sand detail on a walkway near Gateway
Common problems

What paver problems show up most in Gateway?

Heavy use at shared entries and decks

Most housing in ZIP 33716 is multi-family, about 85 percent, and nearly 80 percent of homes are rented. Entry walks, courtyards and pool decks serve many households, so they take far more feet than a single driveway does. Wear shows as dull patches and scuffs where people turn and stop, and pool gates and stair landings take the most. A coat takes that wear instead of the paver face, and matte hides it best. A sealed walk is also easier to wash later, since dirt rests on top of the coat. Photos of those spots help the contractor price the job well, and a manager can attach them to the scope for the owners or the board.

Rain that drains sand from the joints

Annual rain here runs near 50 inches over about 94 wet days, and the heaviest falls come between June and September. Florida's state soil is a fine sand, and water moves through it quickly, so the seams lose loose sand to every hard storm. You may spot sand piled where a downspout empties. Open joints let in soil and weeds. A contractor can top up the sand and seal in a single visit, so the area is not closed for long, and managers who check joints in the fall catch problems early. Waiting usually means a bigger fix, since open seams keep widening with every storm.

Damp shade beside buildings

Gateway is an edge city of offices, stores and apartment blocks, and walls throw shade across the paved areas around them. Landscape guidance links moss and algae on pavers to heavy shade and steady damp. A courtyard that never gets afternoon sun can turn green while the parking apron dries, and walls and parking structures keep sunlight off the low corners. That film is slick underfoot, which matters at stairs and pool gates. Wash and coat belong together, since growth returns fast on bare damp stone. Ask how shaded areas will be handled, and whether a second wash is planned for them.

Past coats nobody wrote down

A building may have changed hands or managers several times, and each may have used a different sealer. The paperwork may be gone. A water-based coat will not go over a solvent-based coat, so the contractor first finds out which one is down. About 79.7 percent of occupied homes in ZIP 33716 are rented, and renters may not know what is on the pavers, so a manager who keeps a record of past coats saves everyone time. A short test on a small patch shows what the stone will accept. Sharing any old invoice helps, and so does a note of which areas were sealed together.

Orange spots from irrigation

UF/IFAS notes that iron is common in Florida well water and leaves rusty deposits on whatever it wets. Landscaped strips run beside nearly every paved walk here. If sprinkler spray reaches the pavers, orange marks build up in the same places and climb walls and doors. Rust is a mineral deposit rather than surface dirt, so rinsing alone seldom clears it, and sealer would trap it underneath. A landscaper can point the heads away from the pavers before the job, so the work is not undone. The contractor can tell you which heads cause trouble during the walk.

Neighborhoods

Where does Gateway start, and who orders paver sealing there?

Gateway is a district rather than a single subdivision. It covers about 30 square miles along Highway 92 and Interstate 275, from Highway 19 and Starkey Road on the west to Tampa Bay on the north and east. Parts of it lie in St. Petersburg and parts in Pinellas Park. Give the contractor your street when you request a free estimate.

The numbers explain the buyer. ZIP 33716 had 18,023 residents, with about 85 percent of housing in multi-family buildings and only about 9 percent in single-family houses. Roughly one home in five is owner-occupied. That means many jobs are ordered by a property manager or an association, so call (727) 591-3365 and say who should receive the estimate.

Residential projects such as Ibis Walk and Peridot Palms sit beside the offices and shops near Highway 92. Gateway Market Center and Gateway Crossings are the retail anchors nearby. If you own a house, a townhome or a condo in or near those blocks, the same sealing steps apply. To get a price, request a free estimate and list the paved areas you care for.

About 85.40 percent of housing in ZIP 33716 is multi-family, and about 79.71 percent of occupied homes are rented. That means many bids go to a property manager or an association, who need each area priced on its own line with the sealer named. Call (727) 591-3365 to ask how a multi-building quote is laid out.

Pricing

What does paver sealing cost in Gateway?

Start with the figure Tampa Bay companies commonly publish, $1.25 to $2.50 per square foot to clean, sand and seal. Open aprons land low in the band, and tight courtyards with planters land high. Old sealer to deal with first adds cost. For a figure on the property you manage, request a free estimate.

Shared sites add steps: notices to residents, move-in dates to avoid, doors to keep clear and a board to satisfy. Write each into the estimate. To have your list added, call (727) 591-3365.

Paved areaTypical exampleClean, sand and seal
300 sq ftSmall patio or walkway$375 to $750
600 sq ftTwo car driveway$750 to $1,500
1,000 sq ftLarge driveway or pool deck$1,250 to $2,500
1,500 sq ftDriveway plus pool deck$1,875 to $3,750

Math based on the $1.25 to $2.50 per square foot that Tampa Bay paver companies publish. Your contractor sets the actual price after seeing the surface. Repairs, leveling and stripping failed sealer are usually extra.

Get a Free Estimate

Contractors sealing a paver driveway at a home in Gateway
How it works

How does a paver sealing job work in Gateway?

Step 1: tour the property

The contractor tours your Gateway property with the manager or an owner and notes where water drains, where shade holds damp and what coat is down. Doors, parking and pool hours are noted so the plan fits daily life. Photos of each area go into the written scope. Gateway properties often have several buildings, so the contractor may tour them in a set order and number the areas, which keeps the written scope easy to follow.

Step 2: wash

The wash clears gray film, shade growth, parking-lot oil and rust from sprinklers. Rinse water stays off doors, windows and plants where pavers meet the building. Stubborn spots get a second pass. Parking-lot oil and tire marks near entry aprons get a closer look, and those areas are washed last so cleaner stone is not tracked over.

Step 3: re-sand

Washing pulls sand from the joints, so new sand is swept in and compacted. Full joints keep the stones locked and keep weeds from rooting on sandy Pinellas ground. Sand is checked against the height of the neighboring stones, and low seams are filled again before the coat goes on.

Step 4: dry

Sealer needs dry stone. After a summer shower the joints can hold water while the top looks dry, and a shaded courtyard lags a sunny lot. If the forecast turns, the work moves, and the manager hears about it. Each area is checked again before the coat goes down. The contractor keeps the manager posted if the date moves, so notices to residents stay accurate.

Step 5: seal and reopen in stages

The sealer goes on in the finish chosen. Large sites are done area by area so residents keep a way in and out. The contractor says when feet, carts and cars can return to each area. A short written summary of what went on helps the next manager. Chairs, planters and bike racks go back after the coat has set, and the manager has the final say on the order.

Services

Complete paver services in Gateway

Plan on four stages for any Gateway site: clean the stone, refill the joints, let it dry, seal it. Each stage has to finish before the next starts. Call (727) 591-3365 and ask how that sequence would run across your buildings.

A site here may include an apartment entry, a townhome drive, a courtyard and a pool deck. Each is a separate line in the scope, with its own size and its own price. When you request a free estimate, list every one so none is missed.

Sealer is water-based or solvent-based, in a matte or wet finish. An earlier solvent-based coat takes the water-based kind off the table, since it cannot go over. For busy entries, matte hides scuffs better. For help choosing, call (727) 591-3365.

Rain falls hardest from June to September, and sealer needs a dry surface. Shaded courts beside buildings dry last, so the contractor schedules them last. To set dates that suit your residents, request a free estimate.

Questions to ask before you hire

  • Will the estimate you hand me list the sealer brand and how many coats go down?
  • Will the insurance certificate you send have my name and address on it?
  • If I give you one flat number, which jobs on the checklist does it pay for?
  • Would a wet-look or a natural-look finish suit my pavers better, and what changes between them?
  • My pool uses salt. Will the sealer or the rinse water bother it or the screen cage?
  • My sprinklers left orange spots near the garage. Can those come out?
  • I have travertine around the pool. Does it need a different product from my driveway pavers?
Photos

What do sealed pavers look like around Gateway?

Freshly sealed paver driveway near Gateway
Sealed paver pool deck near Gateway
Sealed paver patio behind the home near Gateway
Sealed paver walkway to a front door near Gateway
Close view of freshly sealed pavers near Gateway
Paver area with one cleaned half beside a dirty half near Gateway
Contractor cleaning pavers near Gateway
Contractor sealing or sanding pavers near Gateway
Contractor talking through a paver sealing estimate with a homeowner in Gateway
Local

Why local matters in Gateway

A contractor who works Gateway knows trucks, shift workers and residents share these streets. Staging a job around them takes planning. Ask who will lead the work on site. For a contractor who works the Gateway side of Pinellas County, call (727) 591-3365.

Weather is the second factor. Heavy summer rain drains fast through sandy ground, and shaded corners stay wet. A Gateway contractor builds the schedule around both. To ask how yours would run, request a free estimate.

Owner type is the third. A house owner, a townhome association and an apartment manager each need a different kind of estimate. A contractor used to Gateway writes it so each can read it. If that sounds like you, request a free estimate and say which kind you are.

Employers in Gateway include Raymond James Financial, Home Shopping Network and Jabil, and retail lines Highway 92. Mixed-use and residential projects such as Ibis Walk and Peridot Palms sit among them. Pavers at a shared entry or courtyard take foot traffic from residents and visitors alike, so describe how the property is used when you request a free estimate.

Local roots

What is Gateway, and where does it sit?

Anyone driving in from Tampa on the interstate reaches Gateway first. It sits along Highway 92 and Interstate 275 at the west end of the Howard Frankland Bridge. The original bridge span opened in April 1960 and a parallel span followed in 1990. If your building sits near that road, request a free estimate and mention it.

Its edge-city mix of offices and homes grew up around that crossing. Employers such as Raymond James Financial, Home Shopping Network and Jabil have offices in Gateway, and Gateway Market Center brings shoppers in. Gandy Boulevard marks the southern edge and Tampa Bay lies to the north and east. Near any of these Gateway landmarks, call (727) 591-3365 and name your property.

Questions

Frequently Asked Questions

How often should I seal pavers in Florida?

Two to five years separate coats, going by what companies commonly quote. A busy Gateway entry may need attention sooner than a quiet side path. A written list of stages helps you compare bids, and shade and heavy use can shorten the gap. Entries on the shaded side of a building may come due before those in full sun, so ask the contractor to check each side.

What is the average cost to seal pavers in Florida?

Companies publishing around Tampa Bay quote $1.25 to $2.50 per square foot to clean, sand and seal. Your total depends on the size of the area, the old coat and the finish. Request the price per square foot, so every bid reads the same way. The estimate is free. Ask for the price per square foot, so every bid reads the same way.

Which sealer works for pavers in Florida?

The choice is between water-based and solvent-based, and between matte and wet look. An old solvent-based coat limits the choice, since water-based sealer cannot go over it. Ask the contractor which product will go on and why. You choose the finish, and the contractor explains how each one behaves under foot traffic and in rain. A manager can ask for both finishes to be shown on a small test patch, so residents see the difference before the full coat.

What is the average cost to seal pavers at a Gateway townhome or condo?

The same range applies to a townhome or condo, from $1.25 to $2.50 per square foot. Entry walks, drives and decks are measured separately, so you see what each adds. Each area should get a line of its own. That also helps when a board compares two bids and wants each area on its own line.

How often should townhome pavers in Gateway be sealed?

Busy shared areas sit nearer the short end of the two to five years companies commonly quote. Green growth in shade and sand missing from the seams also say it is time. A contractor can walk the property and tell you what the current coat needs, and which areas can wait. For a mixed property, the contractor can split the estimate by building, so each owner sees only the part that applies.

Who orders paver sealing for an apartment or condo community in Gateway?

Usually the property manager or the association board does. The contractor writes the scope for them, with each area listed and priced. Owners of single-family houses order for themselves. Residents are usually told the dates and the closed areas ahead of time, and the manager can post them. Residents are usually told the dates and closed areas ahead of time, and the manager can post them in lobbies and mailrooms.

Can sealing be done in phases on a large Gateway property?

Yes. Many sites are done area by area so residents keep a way in and out. Ask the contractor to list the order of areas and the days each will be closed. Phasing also lets the contractor finish the shaded areas last, when they have had time to dry. A phased plan also spreads the cost over several weeks if the budget calls for it, and it keeps one entrance open at all times.

How long are shared areas closed after sealing?

The contractor gives you the time for each area, and it depends on the product and the weather. Sealer needs a dry surface to start, so a rainy week can move the date. Keep cars, carts and pets off until you are told it is safe. Managers can ask the contractor for a printed notice for each building, listing the area, the dates and the contact. Residents then know where to walk.

Ready for a Free Estimate in Gateway?

Call (727) 591-3365 and tell us about your pavers.

Call (727) 591-3365

Free, no obligation